Skip to content
IDAHO
CATTLE GUARDS

Cattle guards

Cattle guards, supplied and installed

A cattle guard is four decisions: how wide, what load class, flat rail or pipe, and with or without wings. Get those right and the rest is base prep. Buy the guard on its own and set it yourself, or we source it and line up a local crew to put it in the ground.

Guard only

We size it, price it and get it to you. Pickup or delivery in our service area. The excavation and base are yours.

Price the guard only

Guard, installed

Site review, excavation, base, setting, wings and fence tie-in - with the crew lined up and booked for a day that works.

Get it installed

Several crossings

Counties, districts, agencies, contractors and big ranches. Itemised by crossing, supply only or installed.

Bulk and agency quotes

Decision one

How wide

Measure the surface traffic actually uses at its widest point - not the gap between your gate posts, which is the measurement that ends up with a tractor's duals hanging off the end of the rails. Then go wider than that. How much wider depends on what turns in off the road and at what angle.

Most Idaho ranch roads land on a 16 ft guard. Driveways are often 12 or 14 ft. Equipment yards and county roads go up from there.

Sizes and widths in detail

Measuring the opening for a cattle guardLooking down on a road between two fence lines. The travelled surface is measured first, then the guard is sized wider than it so equipment does not run off the end of the rails.GUARD WIDTHTRAVELLED SURFACESHOULDER EACH SIDEMEASURE THE SURFACE EQUIPMENT USES, NOT THE GAP BETWEEN POSTS
Measure the surface traffic actually uses, at the widest point, then size the guard wider than it. How much wider depends on what turns in - we settle it at the site review.
Cattle guard load classesFour load classes as bars of increasing length: ATV and UTV crossings, private and ranch use, heavy ranch and farm equipment, and highway rated. Only a highway rating is accepted on a public road.ATV / UTV CROSSINGPRIVATE / RANCH USEHEAVY RANCH + FARM EQUIPMENTHIGHWAY RATEDAXLE LOAD AND USE INTENSITY →PUBLIC ROADS
A public road needs a highway rating, and only the manufacturer can certify one. We send you the certificate with the quote.

Decision two

What load class

Size for the heaviest thing that crosses, not the average. A loaded silage truck twice a year is the design case, not the pickup that goes over it daily. On a public road you need a highway rating, and that rating comes from the manufacturer's certificate - we send you the document with the quote.

Nobody should take a load rating on trust from a website, including ours.

Heavy duty and highway-rated guards

Decision three

Flat rail or pipe

Flat bar gives a flat running surface that is easier on tyres and feels more solid to drive; it also holds mud longer. Round pipe sheds mud and snow better and is less sure underfoot, which is part of how it works on livestock. Neither is better in the abstract.

What matters more than either is rail spacing, because spacing decides whether stock respect the guard - and spacing is a manufacturer figure, not a preference.

Flat rail compared with pipe railEnd-on section of two cattle guards. On the left, flat bar rails presenting a flat top surface. On the right, round pipe rails presenting a curved top surface.Flat railFLAT RUNNING SURFACEEASIER ON TYRESHOLDS MUD LONGERPipe railROUNDED SURFACESHEDS MUD AND SNOWLESS SURE UNDERFOOTSCHEMATIC - RAIL SIZE AND SPACING PER MANUFACTURER SPEC
Rail size and spacing are the manufacturer's figures, and spacing is what decides whether stock respects the guard. Neither type is "better" - they trade differently in mud and snow.

Decision four

Wings, or no wings

Wings flare out from each end of the guard to the fence line. They stop livestock walking around the end of the rails, and they give equipment somewhere to be when it turns in off the road. If the crossing is at a corner, a junction, or anywhere a trailer swings wide, you want them. When wings are needed.

Published specifications

No published specs yet. We publish a spec once we hold the manufacturer document that states it. Ask us for the spec sheet for any product and we will send it as it was given to us.

We publish a figure once we hold the document that states it, which is why this table is empty rather than full of plausible numbers. When we quote your crossing, the manufacturer's specification comes with it - rail size, spacing, widths, and the load rating with whatever standard it was tested against - exactly as it was given to us.

How to read a cattle guard spec sheet

Other types we handle

  • Concrete and precast — how they compare with steel on cost, install time and cleanout.
  • Driveway guards — the acreage version of the same job, usually narrower and lighter.
  • Pivot and ATV crossings — pages coming; ask us in the meantime and we will size one.

Tell us the opening and what crosses it

Get my free quote